Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   The general information and safety measures
   Removal and installation ступичных assemblages of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Major repairs of racks of a forward suspension bracket
   Removal, major repairs and installation of the bottom levers of a forward suspension bracket
   Replacement of spherical support of the bottom levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, major repairs and installation of racks of a back suspension bracket
   Major repairs of racks of a back suspension bracket
   Removal, major repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross-section stability
   Removal and installation of the back bridge
   Removal and steering wheel installation
   Removal and installation of a steering column
   Major repairs of a steering column
   Removal and installation of assemblage of the lock of ignition/blocking of a wheel
   Removal, major repairs and installation of the steering mechanism
   Replacement of rubber protective covers картера the steering mechanism
   Removal of air stoppers from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the helmsman наcоса
   Removal and installation of external tips of steering draughts
   Removal and installation of steering draught
   Corners of installation of wheels of the car - the general information
+ Body and salon furnish
+ Onboard electric equipment



Removal, major repairs and installation of pins of the back bridge

REMOVAL

 PERFORMANCE ORDER

1. Prop up wedges forward wheels, then поддомкратьте a back of the car and establish it on props. Remove a corresponding back wheel.
2. Remove a brake drum (the Brake system see the Head). On the models equipped ABS, отболтите and the wheel gauge and, without disconnecting electroconducting, clean it aside from ступичной assemblages.
3. For the purpose of minimisation of losses of a brake liquid uncover tank GTTS, enclose under it a polyethylene film and again densely screw, having achieved demanded hermetic sealing. Alternatively, press a clamp a flexible brake hose as it is possible more close to the wheel cylinder.
4. Wipe outside штуцерное connection of a brake tube, give накидную a nut and accurately separate a tube from the wheel cylinder. At once закупорьте the open ends of a tube and the union in order to avoid hit in dirt system. Collect rags traces of the spilt liquid.
5. Turn out bolts of fastening of assemblage of a brake board and separate last from a pin of the back bridge. Remove assemblage of a pin of the bridge from the car. Temporarily fix a brake board on the bridge in pair bolts in avoidance вытягивания drive a cable of a lay brake.
6. Check up pin assemblage on presence of mechanical damages, задиров and agnails. In case of need make replacement.

At all do not undertake correction attempts погнутой a pin.

INSTALLATION

 PERFORMANCE ORDER

1. Carefully smooth out interfaced surfaces of the bridge, assemblage of pins and a brake board. Check up a board condition, in case of need remove the revealed roughnesses with the help надфиля or a fine-grained emery paper.
2. Get assemblage of a pin with a brake board on the regular place, screw fixing bolts and in a diagonal order tighten them with demanded effort.
3. Wipe a brake tube and connect it to a back part of the wheel cylinder. Strongly tighten накидную штуцерную a nut.
4. Remove a clamp/take pressing to a brake hose a polyethylene film from under tank GTTS cover, then establish to the place of a brake drum and pump over a hydraulic contour (the Brake system see the Head). On the models equipped ABS, establish into place the wheel gauge.