Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   The general information and safety measures
   Removal and installation ступичных assemblages of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Major repairs of racks of a forward suspension bracket
   Removal, major repairs and installation of the bottom levers of a forward suspension bracket
   Replacement of spherical support of the bottom levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, major repairs and installation of racks of a back suspension bracket
   Major repairs of racks of a back suspension bracket
   Removal, major repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross-section stability
   Removal and installation of the back bridge
   Removal and steering wheel installation
   Removal and installation of a steering column
   Major repairs of a steering column
   Removal and installation of assemblage of the lock of ignition/blocking of a wheel
   Removal, major repairs and installation of the steering mechanism
   Replacement of rubber protective covers картера the steering mechanism
   Removal of air stoppers from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the helmsman наcоса
   Removal and installation of external tips of steering draughts
   Removal and installation of steering draught
   Corners of installation of wheels of the car - the general information
+ Body and salon furnish
+ Onboard electric equipment



Removal and installation of the steering pump

REMOVAL

 PERFORMANCE ORDER

1. Firmly cock a lay brake, then поддомкратьте redock of the car and establish it on props.
2. Release bolts of fastening of a pulley drive a belt to the steering pump, then ослабьте a belt and throw off it from a pulley. Now turn out fixing bolts and remove a pulley from the pump, having tried to remember its adjusting position.
3. Special clips or clamps press submitting and feeding hoses near to the tank of the steering pump for the purpose of minimisation of losses of a hydraulic liquid.
4. Turn out the fixing screw and remove a collar of fastening of a submitting tube from a basic arm (if that is provided).

5. Release a collar and disconnect from the pump submitting hose, then turn out штуцерный a bolt and disconnect feeding hose. For gathering of a spilt liquid prepare drain capacity. The open ends of hoses/tubes at once закупорьте for the purpose of minimisation of losses of a liquid and in order to avoid hit in hydraulic system of a dirt. Remove sealing washers штуцерного connections of a hydraulic tube.

At assemblage sealing washers are subject to replacement without fail.

6. Turn out bolts of fastening of the pump and take last from assembly скобы.
7. The pump is executed in the form of tight assemblage and regenerative repair is not subject. In default make replacement.

INSTALLATION

 PERFORMANCE ORDER

1. Get the pump on the regular place, screw fixing bolts and tighten them with demanded effort.
2. Establish from both parties штуцерного connections of a feeding tube new sealing washers, then screw штуцерный a bolt. Make sure of correctness of joining of a socket and strongly tighten штуцерный a bolt.
3. Connect to the pump submitting tube, reliably having fixed its collar. Now pressing hoses clips can be removed.
4. Establish the steering pump on basic arms, screw fixing bolts and tighten them with demanded effort.
5. Establish into place a pump pulley while only slightly having tightened fixing bolts. Make adjustment натяжиения a belt, then definitively tighten bolts of fastening of a pulley.
6. In summary "pump over" hydraulic system (see Has undressed Removal of air stoppers from a hydraulic path of system of strengthening of a wheel).