Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   The general information and safety measures
   Removal and installation ступичных assemblages of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Major repairs of racks of a forward suspension bracket
   Removal, major repairs and installation of the bottom levers of a forward suspension bracket
   Replacement of spherical support of the bottom levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, major repairs and installation of racks of a back suspension bracket
   Major repairs of racks of a back suspension bracket
   Removal, major repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross-section stability
   Removal and installation of the back bridge
   Removal and steering wheel installation
   Removal and installation of a steering column
   Major repairs of a steering column
   Removal and installation of assemblage of the lock of ignition/blocking of a wheel
   Removal, major repairs and installation of the steering mechanism
   Replacement of rubber protective covers картера the steering mechanism
   Removal of air stoppers from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the helmsman наcоса
   Removal and installation of external tips of steering draughts
   Removal and installation of steering draught
   Corners of installation of wheels of the car - the general information
+ Body and salon furnish
+ Onboard electric equipment


Removal and installation of racks of a forward suspension bracket

At assemblage the new nut of a coupling bolt ступичной assemblages, and also new nuts of the top support of a rack is required.

REMOVAL

 PERFORMANCE ORDER

1. Open a cowl and check up an impellent compartment on presence распорной bars of the top support of racks of a suspension bracket. In case of need, give nuts of the top support and remove a bar.

2. Prop up wedges back wheels, cock a lay brake, then поддомкратьте redock of the car and establish it on props. Remove a corresponding forward wheel.
3. On the models equipped with the stabilizer of cross-section stability, give a nut of fastening of a rack of a bar of the stabilizer to the bottom lever, remove a washer and the bottom rubber insert.

4. On all models give a nut and take a coupling bolt of fastening ступичной assemblages to a rack.

At assemblage the nut is subject to replacement without fail.

5. By means of mount cautiously lower the bottom lever, liberating a spherical support from the landing collar in the basis ступичной assemblages, - try not to admit an excessive tension of a brake hose. If assemblage does not separate from a rack, with the big screw-driver with a flat sting accurately dissolve sponges of a fixing collar. On the models equipped with the stabilizer of cross-section stability, try not to admit loss of a rubber pillow and a washer of the top support of a rack of a bar of the stabilizer.

The coupling bolt of a spherical support is subject to replacement without fail (in the complete set with the nut).

6. In an impellent compartment remove a plastic cover, then give nuts of the top support of a rack and remove washers.

At nut assemblage are subject to replacement without fail. Take a rack through an arch of a wheel and remove it from the car.

INSTALLATION

 PERFORMANCE ORDER

1. Through a wheel arch get a rack on the regular place, establish washers and screw new top nuts. Tighten nuts with demanded effort, then establish a plastic cover. If the car is equipped распорной by a bar, temporarily screw old nuts, only slightly having tightened them.
2. Enter the bottom part of a rack into gearing with ступичной assemblage. On the models equipped with the stabilizer of cross-section stability place a rack of a bar of the stabilizer on the bottom lever of a suspension bracket, having tracked correctness of an arrangement of the top rubber insert and a washer.
3. Achieve combination of fixing apertures, insert a coupling bolt, screw a new nut and tighten it with demanded effort.
4. Where it is required, establish the bottom rubber insert and a washer of a support of a rack of a bar of the stabilizer. Screw a nut and tighten it with demanded effort.
5. Establish into place a wheel, then lower the car on the earth and tighten wheel bolts with demanded effort.

6. On the models equipped распорной with a bar of racks remove old nuts of fastening of a bar and replace their new (do not forget to enclose a washer), having tightened them with demanded effort.