Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and salon furnish
- Onboard electric equipment
   The general information and safety measures
   Search of causes of failures of an electric equipment
   Safety locks, the relay and breakers - the general information
   Removal and installation of switches
   Replacement of lamps of external lighting and alarm devices
   Replacement of lamps of internal lighting devices
   Removal and installation of assemblages of external lighting and alarm devices
   Adjustment of a direction of an optical axis of head headlights - the general information and replacement of the mechanism of a regulator
   Removal and installation of an instrument guard
   Removal and installation of a cable of a drive of a speedometer
   Removal and installation прикуривателя
   Removal and installation of a small horn of a horn
   Removal and installation of levers of screen wipers
   Removal and installation of the electromotor and draughts of a drive of cleaners of a windscreen
   Removal and installation of the electromotor of a drive of a cleaner of back glass
   Removal and installation of components of washers wind glasses/lenses of head headlights / back glass
   Removal and autoradio tape recorder installation
   Removal and installation of loudspeakers
   Removal and installation of the aerial of a radio receiver
   The anticreeping alarm system/system иммобилизации the engine
   Removal and installation of components of a heating system of forward seats
   Safety pillow - the general information, safety measures and system deactivation
   Removal and installation of components of system of pillows of safety
   Diagnostics of electronic control systems by the engine and safety systems
   + Schemes of electric connections



Removal and installation of the electromotor and draughts of a drive of cleaners of a windscreen

REMOVAL

 PERFORMANCE ORDER

Include screen wipers and stop them in parking position. Disconnect a negative wire from the battery. (The prevention in Section the General information and safety measures) see.


The privodnoj electromotor

 PERFORMANCE ORDER

1. Disconnect from drive the motor electroconducting.

2. Give a nut of fastening of a crank приводной draughts, remove a washer, then disconnect a crank from an electromotor spindle.

3. Turn out fixing bolts and remove assemblage of the electromotor from the car.

Assemblage of the electromotor with приводными draughts.

 PERFORMANCE ORDER

5. Remove levers of screen wipers (see Has undressed Removal and installation of levers of screen wipers).
6. Disconnect from drive the motor electroconducting.
7. Give a plastic nut and release clamps of fastening of the panel обтекателя. Separate the panel обтекателя from the basis of a windscreen and take him aside from draughts of a drive of screen wipers.

8. Remove protective caps from spindles of fastening of both levers, then give nuts and remove flat and sealing washers.

9. Remove assemblage of a drive from the regular place and clean from the car, remembering adjusting position on support of any assemblage of washers and remote plugs.

On models with a link sided steering, probably, it is necessary to release clamps and to remove the top section of a casing of a heater for the purpose of maintenance of sufficient working space.

INSTALLATION

The privodnoj electromotor

 PERFORMANCE ORDER

1. At installation of the new motor preliminary connect it to electroconducting, or it is direct to the battery for the purpose of reduction in parking position.
2. Get the motor on the regular place and strongly tighten fixing bolts.
3. Make sure of correctness of position of levers of both screen wipers (they should be in parking position), then put on a spindle of the motor a crank приводной draughts. Establish a washer, then screw a fixing nut and tighten it with demanded effort.
4. Connect to the motor electroconducting, then connect the battery.


Assemblage of the electromotor with приводными draughts

 PERFORMANCE ORDER

Installation is made in an order, the return to a dismantle order. Track correctness of placing of washers and remote plugs. Tighten with demanded effort of a nut of fastening of levers.