Skoda Felicia

Since 1994 of release

Repair and car operation

Replacement of lamps of external lighting and alarm devices

The general information

At refusal of any lamps накаливания, it is necessary to pay attention to following moments:

a) Before to start replacement, disconnect a negative wire from the battery (see the remark resulted in Section the General information and safety measures);
b) Remember that just burning lamp during even some time remains very hot;
c) Try not to touch a flask of lamps with naked fingers and not to leave on it the fat stains causing decrease of brightness of a luminescence and gradual tarnishing of a reflector;
d) Check quality of electric contact between a socle of a lamp and plugs of its cartridge. Before installation of a new lamp smooth out plugs from corrosion traces. In lamps байонетного type watch, that cartridge contacts densely nestled on socle plugs;
e) Watch, that the replaceable lamp corresponded under the electric characteristics failed.

Head headlights

PERFORMANCE ORDER

1. Turn an access cover counter-clockwise and remove it from a back part of a head block headlight.

2. Disconnect from a lamp electroconducting.

3. Release clamps and take a lamp with a cartridge from a back part of a block headlight. Take a lamp from a cartridge.

4. Try not to touch a flask of a new lamp with naked fingers - take advantage of a paper towel or a napkin. Casually left stains delete by flask rubbing by methyl spirit.
5. Establish a new lamp, having tracked correctness of landing of assemblage in a block headlight.
6. Connect electroconducting and establish an access cover (a label of "TORAHS" upwards).

Forward dimensional fires

PERFORMANCE ORDER

1. Turn an access cover counter-clockwise and remove it from a back part of a head block headlight.
2. Take from a block headlight a cartridge of a lamp of dimensional fire, then take from a cartridge a lamp.

3. Installation is made upside-down. Track, that the access cover has appeared the label of "TORAHS" established on a block headlight upwards.

Forward antifog headlights

PERFORMANCE ORDER

The information resulted more low concerns only models of release till 1998 At the moment of drawing up of the present Management the information on later models was absent.

1. Accurately having hooked a small screw-driver, remove facing of an antifog headlight from the forward party of a bumper.
2. Turn out fixing screws and liberate assemblage of a headlight from a bumper. Disconnect electroconducting and remove a headlight from the car.
3. Release a fixing clamp and take from a headlight a lamp.
4. Try not to touch a flask of a new lamp with naked fingers - take advantage of a paper towel or a napkin. Casually left stains delete by flask rubbing by methyl spirit.
5. Establish a new lamp, having tracked correctness of landing of a reflector and reliability of fixing of assemblage.
6. Connect electroconducting, then establish headlight assemblage in a forward bumper. Strongly tighten fixing screws. Then establish into place the facing panel.

Forward indexes of turns

PERFORMANCE ORDER

1. Find a clamp of fastening of the index of turn in a forward corner of an impellent compartment. Release a clamp and liberate assemblage of the index from a wing. For providing of access to the index of the right turn there can be a necessity for removal from the support of a casing of an air cleaner (the Power supply system see a corresponding Part of the Head).

2. Turn a lamp cartridge counter-clockwise and take it from index assemblage.

3. The lamp socle has байонетную a design, therefore for extraction the lamp should be pressed downwards and slightly to turn counter-clockwise.

4. Installation is made upside-down. Track reliability of fixing of assemblage of the index in a car wing.

Lateral repeaters of forward indexes of turns

PERFORMANCE ORDER

1. Having reached through a wheel arch, push out assemblage of the repeater from a wing.
2. Liberate a cartridge from lens assemblage, then take a lamp.

3. Installation is made upside-down. Track reliability of fixing of a lens in a car wing.

Assemblage of the back combined lantern

PERFORMANCE ORDER

1. In a car luggage space release clamps and remove from a lantern assemblage ламподержателя.

2. All lamps are equipped by socles байонетного type and for extraction should be slightly drowned and turned counter-clockwise.

Pay attention that contact probes of a lamp of a stop-signal of dimensional fire are located asymmetrically that defines unambiguity of landing of a lamp in the holder.

3. Installation is made upside-down. Track reliability of fixing of assemblage ламподержателя.

Top level Stoplight

PERFORMANCE ORDER

1. Release clamps and remove assemblage ламподержателя from the back party of a lantern.

2. Take from the holder a lamp subject to replacement. All lamps are equipped by socles of press type.

3. Installation is made upside-down. Track reliability of fixing ламподержателя in a lantern.

Lantern of illumination of licence plate - models the Sedan and Hetchbek

PERFORMANCE ORDER

1. Accurately having hooked a small screw-driver, liberate assemblage of a lantern from a back door.

2. Liberate a cartridge of a lamp from a lantern lens, then take equipped with a socle of press type a lamp from a cartridge.

3. Installation is made upside-down. Track reliability of fixing of a lens at back doors.