Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and salon furnish
- Onboard electric equipment
   The general information and safety measures
   Search of causes of failures of an electric equipment
   Safety locks, the relay and breakers - the general information
   Removal and installation of switches
   Replacement of lamps of external lighting and alarm devices
   Replacement of lamps of internal lighting devices
   Removal and installation of assemblages of external lighting and alarm devices
   Adjustment of a direction of an optical axis of head headlights - the general information and replacement of the mechanism of a regulator
   Removal and installation of an instrument guard
   Removal and installation of a cable of a drive of a speedometer
   Removal and installation прикуривателя
   Removal and installation of a small horn of a horn
   Removal and installation of levers of screen wipers
   Removal and installation of the electromotor and draughts of a drive of cleaners of a windscreen
   Removal and installation of the electromotor of a drive of a cleaner of back glass
   Removal and installation of components of washers wind glasses/lenses of head headlights / back glass
   Removal and autoradio tape recorder installation
   Removal and installation of loudspeakers
   Removal and installation of the aerial of a radio receiver
   The anticreeping alarm system/system иммобилизации the engine
   Removal and installation of components of a heating system of forward seats
   Safety pillow - the general information, safety measures and system deactivation
   Removal and installation of components of system of pillows of safety
   Diagnostics of electronic control systems by the engine and safety systems
   + Schemes of electric connections










Removal and installation of assemblages of external lighting and alarm devices

Before to start to work do not forget to disconnect a negative wire from the battery (the prevention resulted in Section the General information and safety measures) see.


Head headlights

 PERFORMANCE ORDER

1. Remove both lobbies of the index of turn.
2. On models of release till 1998 turn out the left and right bolts of fastening of the panel передка (access to bolts opens through apertures under installation of indexes of turns). Also turn out two screws of fastening of the top part of the panel to a cross-section beam of the lock of a cowl. Give fixing nuts in a back part of the panel, then remove last from the car.

3. On models of release since 1998 turn out the fixing screw, then remove the decorative cover established between a head block headlight and a forward bumper.

4. On all models turn out the top and bottom screws of fastening of a head block headlight.

5. Take a block headlight from the nest and disconnect electroconducting.

6. Having turned assemblage of a regulator of a direction of an optical axis, disconnect it from a back part of a block headlight, then definitively remove a headlight.

7. In case of need accurately release fixing clamps and remove from a block headlight a lens. Remove from a block headlight a sealant, check up its condition, in case of need replace.

8. Installation is made upside-down. All fixture should be tightened with demanded effort. Track reliability защелкивания clamps and regulator connection. In summary it is necessary to check up installation of an optical axis of a headlight (the Section Adjustment of a direction of an optical axis of head headlights - the general information and replacement of the mechanism of a regulator see).


Assemblages of forward indexes of turns

 PERFORMANCE ORDER

1. Find a clamp of fastening of assemblage of the index in a forward corner of an impellent compartment of the car. Wring out a lock uvula and liberate assemblage of the index from a car wing.

2. Turn and take a cartridge with the lamp of the index established in it. In case of need for simplification of access to the index remove from the support an air cleaner casing (the Power supply system see a corresponding Part of the Head).

3. Installation is made upside-down. Track reliability защелкивания an assemblage clamp.


Forward antifog headlights

 PERFORMANCE ORDER

The information resulted more low concerns only models of release till 1998 fresher data at the moment of drawing up of the present Management were absent.

1. Having hooked a small screw-driver with a flat sting, accurately remove facing of an antifog headlight from a forward bumper of the car.
2. Turn out fixing screws and take a headlight from the landing nest in a car bumper. Disconnect electroconducting and remove a headlight from the car.
3. Installation is made upside-down. In case of need rotation of the adjusting screw correct position of an optical axis of a headlight.

Lateral repeaters of forward indexes of turns

 PERFORMANCE ORDER

1. Through a wheel arch push out assemblage of the repeater from a car wing.

2. Liberate a cartridge and remove a lens.

3. Installation is made upside-down. Track reliability of fixing of a lens of the repeater.


Assemblages of the back combined lanterns

 PERFORMANCE ORDER

1. Release clamps and remove assemblage ламподержателя from a back part of a lantern.

2. Give fixing nuts and remove assemblage of a lantern from the car (together with a sealant) (see an accompanying illustration). Check up a sealant condition, in case of need make replacement.

3. Installation is made upside-down. Track correctness of landing of a sealant.


Top level Stoplight

 PERFORMANCE ORDER

1. Turn out fixing screws and separate assemblage of a stoplight from an internal wall of a door of a back.

2. Disconnect electroconducting and remove assemblage from the car.

3. Installation is made upside-down.


Lantern of illumination of back licence plate

 PERFORMANCE ORDER

1. Accurately having hooked a small screw-driver with a flat sting, liberate assemblage from a back door.
2. Take a cartridge and remove a lens.
3. Installation is made upside-down. Track reliability of fixing of a lens.