Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
- Engine repair
   - Repair without extraction from the car of the petrol engine of 1.3 l
      The description of the basic knots and mechanisms
      Check of a condition of shatunno-piston group on hearing and measurement компрессионного pressure in cylinders
      Reduction of the piston of the first cylinder in position of the top dead point (ВМТ)
      Removal and installation of a cover of a casing of a camshaft
      Removal, check of a condition and installation of assemblage of an axis коромысел
      Removal and installation of a head of cylinders in gathering with the inlet pipeline and a final collector
      Removal, check of a condition and installation of a forward cover, chain and asterisks of drive ГРМ
      Removal, check of a condition and installation of components of the oil pump
      Removal and pallet installation картера the engine
      Replacement of epiploons of a cranked shaft
      Removal, check of a condition and flywheel installation
      Check of a condition and replacement of rubber pillows of support of a suspension bracket of the power unit
      Removal, installation and adjustment of effort of a tension of a belt of a drive of auxiliary units
   + Repair without extraction from the car of the petrol engine of 1.6 l
   + Repair without extraction from the car of the diesel engine
   + Dismantle of the power unit and engine major repairs
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and salon furnish
+ Onboard electric equipment



Replacement of epiploons of a cranked shaft

The right epiploon (from outside a pulley)

 PERFORMANCE ORDER

1. Remove a pulley of a cranked shaft (see Has undressed Removal, check of a condition and installation of a forward cover, a chain and asterisks of drive ГРМ).

2. Cautiously having hooked a screw-driver with a flat sting, take an epiploon from a cover of a chain of drive ГРМ. Try not to damage condensed surfaces of a cover and a pin of a cranked shaft.

3. Alternatively, drill or pierce in a face surface of an epiploon pair of small apertures and screw in them саморезы. Now it is possible to take from a cover, having grasped heads саморезов flat-nose pliers.
4. Carefully wipe and polish walls of a nest of an epiploon, and also a surface of a pin of a cranked shaft - from condensed surfaces any roughnesses, agnails and the teases, capable to lead to fast failure of a new epiploon should be removed.

5. Grease with pure impellent oil of a sponge of a new epiploon, and zapressujte/begin to knock last sponges inside in a nest in a casing заподлицо with an external surface of a cover газораспределительной chains. In quality оправки for epiploon landing it is possible to take advantage of a face head of the corresponding size or a piece of a pipe of suitable diameter which should rest only against rigid external edge of a face surface of an epiploon.

6. Rags collect all traces of oil, then establish a pulley of a cranked shaft (see Has undressed Removal, check of a condition and installation of a forward cover, a chain and asterisks of drive ГРМ). We will notice, at fixing of a cranked shaft from проворачивания in the course of pulley installation it is necessary to remove the pallet картера for the purpose of a possibility of the control of position of a persistent washer.


The left epiploon (from outside a flywheel)


 PERFORMANCE ORDER

1. Remove a flywheel (see Has undressed Removal, check of a condition and flywheel installation).

2. Accurately pierce or drill in a face surface of an epiploon two apertures and screw in them саморезы. Take an epiploon from the nest in a wall of the block of cylinders, having grasped heads of screws flat-nose pliers.

3. Carefully wipe and polish walls of a nest of an epiploon, and also a surface of a pin of a cranked shaft - from condensed surfaces any roughnesses, agnails and the teases, capable to lead to fast failure of a new epiploon should be removed.
4. Grease with pure impellent oil of a sponge of a new epiploon, and zapressujte/begin to knock last sponges inside in a nest in картере the engine.
5. Manually put on a new epiploon a pin of a cranked shaft, accurately having translated it through a coat hanger and запрессуйте it in a nest so that the external end face has appeared in regular intervals on all perimetre is pressed a persistent surface of a coat hanger. In case of need the epiploon can be begun to knock in a nest a hammer with soft the brisk.
6. Remove the rests of greasing and establish into place a flywheel (see Has undressed Removal, check of a condition and flywheel installation).