Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
- Engine repair
   + Repair without extraction from the car of the petrol engine of 1.3 l
   - Repair without extraction from the car of the petrol engine of 1.6 l
      The description of the basic knots and mechanisms
      Reduction of the piston of the first cylinder in position of the top dead point (ВМТ) the end of a step of compression
      Check компрессионного pressure - an order of carrying out and interpretation of results
      Removal and installation of a belt of drive ГРМ and its covers
      Removal, check of a condition and installation of cogwheels and натяжителя a belt of drive ГРМ
      Removal, installation and adjustment of effort of a tension of a belt of a drive of auxiliary units
      Removal and installation of a cover of a head of cylinders
      Replacement of an epiploon of a camshaft
      Replacement of epiploons of a cranked shaft
      Removal and installation of a head of cylinders in gathering with the inlet pipeline and a final collector
      Check of serviceability of functioning of hydraulic pushers
      Removal, check of a condition and flywheel installation
      Check of a condition and replacement of support of the power unit
      Removal and pallet installation картера the engine
      Removal and installation of the oil pump and маслозаборника
   + Repair without extraction from the car of the diesel engine
   + Dismantle of the power unit and engine major repairs
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and salon furnish
+ Onboard electric equipment


Removal and pallet installation картера the engine

REMOVAL

 PERFORMANCE ORDER

1. Park the car on an equal horizontal surface, whenever possible with a firm covering. Cock a lay brake and prop up wedges back wheels.
2. Поддомкратьте redock of the car also establish it on props.
3. Disconnect a negative wire from the battery.
4. Merge impellent oil.
5. Disconnect a reception pipe of system of release of the fulfilled gases from a flange of a final collector (the Power supply system see the Head). Having removed with rubber подвесов, lower sections of system of release of the fulfilled gases, having provided adequate access to the pallet картера.

At lowering of system of release of the fulfilled gases try not to admit натягивания l-probe electroconducting - it will be preliminary correct it to disconnect.

6. Moving on pallet perimetre, in stages ослабьте also turn out fixing bolts.

7. Обстучав a palm, separate the pallet from the block of cylinders and take it from under the car.
8. Taking an opportunity, check up a condition and passableness of a tube and the mesh filter маслозаборника the pump. In case of need remove the pump (see Has undressed Removal and installation of the oil pump and маслозаборника) and clean (or replace) маслозаборник.

INSTALLATION

 PERFORMANCE ORDER

1. Carefully smooth out interfaced surfaces, completely having removed from them the rests of a material of an old lining or hermetic. Then wipe surfaces the rags moistened in acetone.
2. Impose on an interfaced surface of the pallet a pillow of silicone hermetic with section Ø 2 ÷ 3 mm, leading round fixing apertures from within.

 It is not necessary to be zealous excessively, imposing hermetic - hit of surpluses in the pallet картера can lead to infringement of passableness of the mesh filter маслозаборника and, as consequence, to development of oil starvation of internal components of the engine.

3. Having imposed hermetic, at once press the pallet to the block. Not to admit discrepancies, temporarily screw in болтовые apertures of the block pair of directing hairpins М6. Tighten fixing bolts by hand.
4. In stages tighten bolts with demanded effort. Before refuelling of the engine by oil wait time necessary for hardening of hermetic.
5. Hang out sections of system of release of the fulfilled gases and connect to a final collector its reception pipe (the Power supply system see the Head).
6. Lower the car on the earth and fill in in the engine necessary quantity of engine oil of a demanded grade.