Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
- Engine repair
   + Repair without extraction from the car of the petrol engine of 1.3 l
   - Repair without extraction from the car of the petrol engine of 1.6 l
      The description of the basic knots and mechanisms
      Reduction of the piston of the first cylinder in position of the top dead point (ВМТ) the end of a step of compression
      Check компрессионного pressure - an order of carrying out and interpretation of results
      Removal and installation of a belt of drive ГРМ and its covers
      Removal, check of a condition and installation of cogwheels and натяжителя a belt of drive ГРМ
      Removal, installation and adjustment of effort of a tension of a belt of a drive of auxiliary units
      Removal and installation of a cover of a head of cylinders
      Replacement of an epiploon of a camshaft
      Replacement of epiploons of a cranked shaft
      Removal and installation of a head of cylinders in gathering with the inlet pipeline and a final collector
      Check of serviceability of functioning of hydraulic pushers
      Removal, check of a condition and flywheel installation
      Check of a condition and replacement of support of the power unit
      Removal and pallet installation картера the engine
      Removal and installation of the oil pump and маслозаборника
   + Repair without extraction from the car of the diesel engine
   + Dismantle of the power unit and engine major repairs
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and salon furnish
+ Onboard electric equipment


Removal, installation and adjustment of effort of a tension of a belt of a drive of auxiliary units

The general information

Depending on a car complete set auxiliary приводной the belt is used for a drive from a pulley of a cranked shaft of such devices, as the generator, the steering pump and the compressor of the conditioner of air.

On some models the multicostal auxiliary belt is equipped by the device of automatic adjustment of a tension (depending on a route of a lining and quantity of resulted components). On other models adjustment of a tension of a belt is made by change of position of the generator.

At belt installation it is necessary to take care of adjustment of effort of its tension.

REMOVAL

 PERFORMANCE ORDER

1. Park the car on an equal platform, cock a lay brake and prop up wedges back wheels. Release nuts of fastening of the right forward wheel.
2. Поддомкратьте redock of the car also establish it on props. Remove the right forward wheel.
3. Turn out screws of fastening of a cover of a belt.
4. Check up a belt on presence of factory directional markers of rotation. In case of need put corresponding marks independently.


Models with automatic натяжителем an auxiliary belt


 PERFORMANCE ORDER

Having thrown рожковый with a key the central nut натяжителя, develop last clockwise, overcoming effort of a spring.


Models without automatic натяжителя an auxiliary belt

 PERFORMANCE ORDER

1. On one-two turn ослабьте the top and bottom bolts of fastening of the generator.
2. Shift the generator down to an emphasis, turning it round the top support and overcoming resistance of a spring.


All models


 PERFORMANCE ORDER

Remove a belt from a generator pulley, then - from other pulleys.

Installation of a belt and adjustment of effort of its tension

 PERFORMANCE ORDER

At belt installation observe a direction of its rotation, being guided on corresponding marks.

Put on a belt a pulley of a cranked shaft. Track that belt edges have got in the correct image to reciprocal streams of a pulley.


Models with automatic натяжителем


 PERFORMANCE ORDER

1. A nakidnym key develop натяжитель a belt for the central nut clockwise.
2. Get a belt the flat party under a roller натяжителя, then throw with it corresponding pulleys. Track correctness of hit of edges of a belt in streams of pulleys.
3. The belt tension will occur automatically at release натяжителя.


Models without automatic натяжителя

 PERFORMANCE ORDER

1. Overcoming resistance of a spring, some times shift the generator down to an emphasis, checking serviceability of its returning in a starting position at release. In case of need release bolts for a half-turn.
2. Keeping the generator in the wrung out position, put on a belt its pulley. Release the generator - the belt thus should stretch under the influence of a spring.
3. Without tightening generator bolts, start the engine, allow to it to work on single turns within nearby 10 seconds.
4. Muffle the engine and tighten with demanded effort at first the bottom bolt, then top.


All models

 PERFORMANCE ORDER

1. Establish into place a belt cover. Strongly tighten bolts of its fastening.
2. Establish the right forward wheel and lower the car on the earth. Tighten nuts of fastening of a wheel with demanded effort.