Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
- Systems of cooling, heating
   The general information and safety measures
   Detachment and replacement of hoses of system of cooling
   Removal, check of a condition and radiator installation
   Removal, check of serviceability of functioning and thermostat installation
   Check of serviceability of functioning, removal, installation, dismantling and assemblage of the fan of system of cooling
   Check of serviceability of functioning, removal and installation of electric switches and gauges of system of cooling
   Removal, installation, dismantling and assemblage of the water pump
   System of heating/ventilation of salon - the general information
   Removal and installation of components of system of heating/ventilation of salon
   Air central air - the general information and safety measures
   Removal and installation of components of a central air of air
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and salon furnish
+ Onboard electric equipment


Removal and installation of components of system of heating/ventilation of salon

The models which have been not equipped with a central air of air

Assemblage of a casing of a heater

 PERFORMANCE ORDER

1. In case of need give nuts of fastening of the top support of racks of a suspension bracket and remove from the car rack-mount распорку.

2. Operating according to the instructions resulted in the corresponding Part of the Head the Power supply system, execute following procedures:

a) On petrol models 1.3 of l SPFI remove air cleaner assemblage;
b) On petrol models 1.3 of l MPFI отболтите also remove from the inlet pipeline assemblage of the case of a throttle. Take assemblage aside, without disconnecting an accelerator cable, electroconducting and connecting hoses;
c) On petrol models 1.6 of l remove a sleeve of an inlet air inlet;
d) On diesel models remove the top section of the inlet pipeline.

3. Release clamps of fastening of an air inlet to the top part of a casing of a heater...

... Take an air inlet from an impellent compartment.

4. Remove the battery (the engine Electric equipment see the Head).
5. Remove an instrument guard and lighter (the Onboard electric equipment see the Head).
6. Find and disunite an electric socket of the control panel of system of heating/ventilation of salon on a casing left-hand side.

If access to a socket is limited, it рассоединение can be made after casing removal.

7. Through an aperture under installation прикуривателя release a clamp of fastening of a sleeve of giving of air in a foot well to the basis of a casing of a heater.

8. In an impellent compartment press hoses of a heating path for the purpose of minimisation of losses of a cooling liquid. Enclose under unions of the heat exchanger of a heater rags, then release collars and disconnect both hoses. At once смойте the spilt cooling liquid water. A heater casing impose with rags.

9. Give nuts of fastening of assemblage of a casing of a heater to a partition of an impellent compartment.

10. Ask the assistant to make sure that the control panel is liberated by system from the panel of devices, then lift assemblage of a casing with the control panel and remove it from the car,

... In process of providing of access having disconnected an electroconducting socket Lay assemblage by unions upwards for the purpose of minimisation of losses of a cooling liquid.

11. Installation is made upside-down. It is necessary to give special attention to following moments:

a) Before installation check up a condition переборочной linings, in case of need make its replacement;
b) Track correctness of landing of assemblage of a casing and reliability of fastening of air lines and branch pipes, only after that start a tightening of fixing nuts;
c) Track reliability of fastening on unions of the heat exchanger of corresponding hoses;
d) In summary add in cooling system necessary quantity of a mix of demanded structure.


The control panel of system of heating/ventilation of salon

 PERFORMANCE ORDER

1. Remove assemblage of a casing of a heater with the control panel.

2. Try to remember adjusting position of each of drivers cables (tips of cables have colour marks). Then, by means of flat-nose pliers release fixing clips and disconnect cables from the panel.

3. Disconnect electroconducting from drive the motor of the fan of a heater, then separate the panel from a casing.

4. Assemblage is carried out upside-down. Track correctness of a lining and reliability of fastening on the regular places of all drivers cables. A feather definitive installation of assemblage of a casing on the car check up serviceability of functioning of switches of management.


The electromotor of a drive of the fan - petrol models

 PERFORMANCE ORDER

1. Release fixing and remove an air inlet from a heater casing.

2. For the purpose of providing of access remove the battery.

3. Walk on electroconducting from the electromotor the truth of the fan of a heater to a socket. Disunite a socket...

Also liberate from a casing the rubber plug of a plait through passage, then extend a plait from a casing.

4. Turn out fixing screws, release clamps and remove assemblage of a basic plate of the electromotor of the fan from a heater casing.

5. Liberating from clamps, remove covers,

Then ослабьте the screw

Also separate the motor from a plate.

6. Assemblage is made upside-down. In summary do not forget to establish into place the battery and to check up rotation freedom крыльчатки the heater fan.


The electromotor of a drive of the fan - diesel models

 PERFORMANCE ORDER

1. For the purpose of providing of access remove the battery.
2. Release clamps and remove from a casing of a heater an air inlet.
3. Disunite a socket of electroconducting of the fan.

4. Give fixing nuts and remove assemblage of a basic plate of the electromotor from a heater casing.

5. For the purpose of providing of access to the motor, release clamps and remove covers. Turn out a coupling bolt and remove the motor from a basic plate.
6. Installation is made upside-down. In summary establish into place the battery and check up rotation freedom крыльчатки.


The resistor of the electromotor of the fan of a heater - petrol models

 PERFORMANCE ORDER

1. The resistor is in an impellent compartment and is fixed on the right wall of assemblage of a casing of a heater. On models with a link sided steering for providing of access to the resistor it is necessary to remove the battery.
2. Disunite an electric socket, then liberate the resistor from clamps and remove it from a casing.

3. Installation is made upside-down. Track reliability of fastening of the resistor.


The resistor of the electromotor of the fan of a heater - diesel models

 PERFORMANCE ORDER

1. The resistor is in an impellent compartment and is fixed on the left wall of assemblage of a casing of a heater. For providing of access to the resistor it is necessary to remove the battery.
2. Disunite electric sockets. Try to remember an order of their connection.
3. Turn out fixing screws and remove the resistor from a casing.
4. Installation is made upside-down.


The heater heat exchanger - petrol models

 PERFORMANCE ORDER

1. Remove a heater casing.

2. Turn out the fixing screw and take the heat exchanger from a casing.

Try not to wound fingers about keen edges of plates of the heat exchanger!

3. Before installation check up a condition sealing пенопластовой weights of the heat exchanger. Accurately get assemblage on the regular place in a casing and strongly tighten the fixing screw. Then establish into place a casing.


The heater heat exchanger - diesel models

 PERFORMANCE ORDER

1. On models with a link sided steering remove the battery.
2. On all models in an impellent compartment press clamps the hoses going to the heat exchanger of a heater. Enclose under unions rags, then release collars and disconnect both hoses. Collect traces of the spilt liquid, impose with rags a heater casing.

3. Release clamping bolts and disconnect приводные cables from draught of the thermostat of the heat exchanger. Release a clip and disconnect a cover of the top cable, then give the top and bottom fixing nuts and remove from a casing the executive lever заслонки.

1 — the Fixing nut
2 — Privodnoj a cable
3 — Privodnoj a cable
4 — Directing a cable
5 — the Executive lever
6 — Clamping a bolt
7 — the Cable
8 — Clamping a bolt

4. Accurately liberating from clamps, remove the top part of a cover of the heat exchanger from a heater casing.
5. Cautiously take the heat exchanger.

Do not cut fingers about keen edges of plates!

6. Installation is made upside-down. Do not forget to check up a condition of sealing weight.


The models equipped with the conditioner of air

At all do not disconnect refrigerator lines (the Section air Central air - the general information and safety measures see)!


Assemblage of a casing of a heater with the control panel

It is necessary to charge performance of procedures of removal and assemblage installation to experts of a workshop of car-care centre in view of necessity of a detachment of refrigerator tubes from the broad valve of evaporator K/V.

The electromotor of a drive of the fan of a heater

 PERFORMANCE ORDER

1. In an impellent compartment remove clamps and remove from a casing of a heater a thermofilter.
2. Find and disunite a socket of electroconducting of the motor of the fan in a forward part of a casing. Push the rubber plug through passage in a casing.
3. Disconnect a vacuum hose from диафрагменной assemblages inlet заслонки. Also disconnect a rod from draught of a diaphragm.
4. Turn out fixing screws, release collars and, liberating electroconducting, remove an air inlet from the top part of a casing of a heater.
5. Turn out fixing screws and remove assemblage drive the electromotor.
6. Installation is made upside-down. Track correctness of landing of the plug of electroconducting through passage. В the conclusion check up serviceability of functioning заслонки an air inlet.


The resistor of the electromotor of the fan

 PERFORMANCE ORDER

1 Resistor is located in an impellent compartment on the left wall of a casing of a heater. For the purpose of providing of access to the resistor remove the battery.
2 Disunite an electric socket, liberate the resistor from clamps and remove it from a casing.
3 Installation is made upside-down. Track reliability of fastening of the resistor on a casing.


The heater heat exchanger


 PERFORMANCE ORDER

It is necessary to charge performance of procedures of removal and heat exchanger installation to experts of car-care centre in view of necessity of a detachment of refrigerator lines from the broad valve of the evaporator (the Section air Central air - the general information and safety measures see).