Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
- Coupling
   The general information
   Removal and installation of a pedal of coupling
   Removal, installation and adjustment of a cable of a drive of coupling
   Removal, check of a condition and installation of assemblage of coupling
   Removal, check of a condition and installation of the mechanism of deenergizing of coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and salon furnish
+ Onboard electric equipment



Removal, installation and adjustment of a cable of a drive of coupling

REMOVAL

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. In car salon under the panel of devices disconnect an auxiliary spring from drive a coupling cable. Remove a clamp and disconnect a tip of a cable from assemblage of a pedal of coupling.
3. Return to an impellent compartment and find трансмиссионный the end drive a coupling cable.

4. On models with a right-hand steering remove a lock clip from the cable core, then give an adjusting nut and remove from a cable a tip and the rubber remote plug. Liberate a cover of a cable from a basic arm and pass through a cable through the rubber protective cover, directing holder, the rubber remote plug and a washer.

5. On models with a link sided steering remove a lock clip of the core of a cable, then give an adjusting nut and remove from the end тросовой assemblages a washer, the rubber remote plug and directing holder. Liberate a cover of a cable from the lever of deenergizing of coupling and remove from it a tip, the rubber remote plug and directing holder.

1 — the Nut
2 — the Washer
3 — the Rubber remote plug
4 — the Washer
5 — the Clamp
6 — the Lever of deenergizing of coupling
7 — the Holder

6. On all models, moving back on a cable, liberate it from intermediate clamps. Try to remember more precisely a route of a lining of a cable in an impellent compartment. Pass through a cable through a partition of an impellent compartment and take it from the car. Remove directing holder and the plug through passage from the end of a cable turned to a partition.
7. Attentively examine a cable on presence of signs of deterioration of tips and mechanical damages of a cover. Whether check up the core was wiped somewhere. Make sure of serviceability of functioning of a cable - the core should move freely in a cover. Do not forget that the cable removed from the car can seem quite serviceable whereas, being established on a regular place it appears disabled. The cable being in a doubtful condition is subject to replacement.

INSTALLATION

 PERFORMANCE ORDER

1. Slightly grease with universal greasing cable tips, then put on on turned towards a partition of an impellent compartment the cable end the rubber plug through passage and directing holder.
2. Pass a cable through a partition, having tracked correctness of landing of the plug through passage and a directing holder.
3. In car salon fix a cable tip on a coupling pedal. Track reliability of landing of a clamp.
4. Return to an impellent compartment and, watching correctness of a lining of a cable, fix it in intermediate directing clamps.
5. On models with a right-hand steering dress on трансмиссионный the end of a cable a washer, the rubber remote plug directing a holder and a rubber protective cover. Track correctness of landing of a directing holder in a basic arm, then put on a cable an internal tip, the rubber remote plug and an external tip.
6. On models with a link sided steering put on a cable directing holder, the rubber remote plug and a tip, then fix a cable on the lever of deenergizing of coupling. Plant on a cable directing holder, the rubber remote plug and a washer, check up correctness of placing of components, then screw an adjusting nut.
7. Connect a negative wire to the battery, then pick up an auxiliary spring to a coupling pedal. Now it is possible to start adjustment drive a cable.

ADJUSTMENT

 PERFORMANCE ORDER

1. Adjustment of a cable of a drive of coupling is made by check of height of position of a pedal in relation to the arm. At correct adjustment the coupling pedal should settle down level with brake ( 3 mm), and in тросовой to assemblage to be absent any люфт.
2. For updating performance find in an impellent compartment located on картере РКПП the cable end.
3. Remove a clamp from the core of a cable and adjust position of a pedal by rotation of an adjusting nut on the part of a tip equipped with a carving. Having achieved demanded result, establish into place a clamp and make sure of density of its landing in on the deenergizing lever / a basic arm.