Skoda Felicia

Since 1994 of release

Repair and car operation


Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
- The power supply system
   + The power supply system of the carburettor engine of 1.3 l
   + System of the central injection (SPFI) the petrol engine
   + System of the distributed injection (MPFI) the petrol engine
   - The power supply system of the diesel engine
      The general information and safety measures
      Removal and installation of assemblage of an air cleaner and components of an inlet path
      Removal, installation and adjustment of a cable of an accelerator
      Removal and installation of the gauge of the expense of fuel
      Removal and installation of a fuel tank
      Removal and installation ТНВД
      Check and adjustment of the maximum turns of the engine and idling turns
      Check of installation of turns of fast idling
      Check and updating of installation of phases of injection ТНВД
      Removal and installation of atomizers
      Removal and installation electromagnetic запорного the valve
   + Systems of decrease in toxicity and release of the fulfilled gases
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and salon furnish
+ Onboard electric equipment

Removal and installation of atomizers

At service of atomizers it is necessary to observe special safety measures. Remember that pressure of operation of atomizers very highly and hit of a stream from a nozzle on open sites of a body can lead to reception of serious traumas. Composers of the present Management recommend to charge performance of all carried out under the pressure of system checks to the qualified experts of a car repair shop.

The preventions resulted in Section the General information and safety measures see.


The general information

Atomizers in the course of engine functioning are subject to deterioration that is why their condition should be checked not less often than each 100 000 km (60 000 miles) car run. Exact diagnostics of a condition of atomizers, their major repairs and calibration should be left to experts. The order of procedure of revealing of defective atomizers (leaders to occurrence of a detonation or excessive smoke blanketing) is more low described.

Start the engine and arrange its working on turns of fast idling. Serially ослабьте штуцерные connections of each of atomizers, preliminary having imposed with their rags for gathering of passed fuel. At easing of the union of a defective atomizer the taking place detonation or excessive smoke blanketing will stop.

REMOVAL

 PERFORMANCE ORDER

At all it is not necessary to suppose hit in dirt atomizers. Do not drop the removed atomizers, do not try to clean them by means of a needle.

1. Disconnect a negative wire from the battery.
2. Cover the generator with pure rags for protection against hit on it spilt дизтоплива.
3. Carefully wipe surfaces round atomizers and their nuts штуцерных connections. Disconnect from atomizers returnable tubes.
4. Wipe surfaces around штуцерных connections of submitting tubes and disconnect the last from atomizers and back part ТНВД (tubes act in film uniform assemblage). Giving a connection nut, keep second half of socket on the pump from проворачивания the second wrench. Remove assemblage of tubes from the engine. At once закупорьте open unions in order to avoid hit in dirt system.

5. By means of a deep face head on 27 mm turn out each of atomizers of a head of cylinders and remove them from the engine.

6. Remove and will throw out thermoprotective washers - at assemblage they are subject to replacement without fail.

INSTALLATION

 PERFORMANCE ORDER

1. Establish on a head of cylinders new thermoprotective washers of atomizers. Remember that washers should be established by the concave party downwards (to a head).

2. Screw atomizers in the landing nests in a head and tighten them with demanded effort.

3. Connect fuel tubes, having tightened nuts штуцерных connections with demanded effort. Establish on tubes all necessary clips and clamps.
4. Connect to each of atomizers returnable tubes. Connect the battery and check up serviceability of functioning of the engine.