Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
- The power supply system
   + The power supply system of the carburettor engine of 1.3 l
   - System of the central injection (SPFI) the petrol engine
      The general information and safety measures
      Removal and installation of assemblage of an air cleaner
      The vacuum switch of a control mean in temperature of soaked up air
      Removal, installation and adjustment of a cable of an accelerator
      Removal and installation of components of system Bosch Mono-Motronic
      Removal and installation of assemblage of a gasoline pump and the gauge of the expense of fuel
      Removal and installation of a fuel tank
      Dump of residual pressure in the power supply system
      Removal and installation of the inlet pipeline
      Check of functioning and adjustment of system of injection
      Neetilirovannoe fuel - the general information and use rules
   + System of the distributed injection (MPFI) the petrol engine
   + The power supply system of the diesel engine
   + Systems of decrease in toxicity and release of the fulfilled gases
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and salon furnish
+ Onboard electric equipment
co na erekcj? bez recepty, mi?dzy в россии | Житель заказал букет из миллиона алых роз.


Removal and installation of assemblage of an air cleaner

Components of assemblage of an air cleaner

1 — the Top cover of an air cleaner
2 — the Filtering element
3 — the Valve-switch of management in temperature of soaked up air
4 — the Sealing lining
5 — an air cleaner Casing
6 — the Fixing plate
7 — the Vacuum capsule

8 — the Inlet mouth (series engines 135В)
9 — the Inlet sleeve
10 — the Inlet mouth (series engines 136В)
11 — the Rubber pillow of a support
12 — the Support
13 — Rezonatornaja a box (series engines 136В)
14 — the Sleeve of giving of the warmed-up air

REMOVAL

 PERFORMANCE ORDER

1. Release the assemblages located on perimetre wire clamps, turn out three fixing bolts and remove the top cover of an air cleaner. Take filtering element.

2. Liberate from an intermediate clamp on a forward part of a casing of an air cleaner an accelerator cable...

Disconnect a sleeve of giving of the warmed-up air from a casing of the thermosensitive valve...

... On the models equipped with engines of a series 136В, release a collar and disconnect an inlet air sleeve from a casing of an air cleaner or a resonator box.

3. Slightly raise an air cleaner casing, having separated it from the throttle case. Disconnect passing under a casing and going to the throttle case a vacuum tube of management of the thermosensitive gauge-switch. The second, going to a capsule, the vacuum hose can be left by the connected.

4. Remove from the top cover of the engine the big ventilating branch pipe). Liberate from clamps on the bottom party of a casing of an air cleaner small шлаг, going from the top cover of the engine and a hose of a purge of a coal adsorber.

5. Now the air cleaner casing can be taken from an impellent compartment.

6. In case of need the inlet mouth of an air cleaner on series engines 135В can be removed after a reversing of the fixing screw.

7. For removal of a casing of the thermosensitive valve of management in temperature of soaked up air disconnect from a capsule a vacuum tube,

Then release two spring clamps...

Also remove a casing, having shifted it forward.

8. On the models equipped with the engine of a series 136В, in an inlet air line the box that allows in an essential measure to lower intensity of a noise background is established резонаторная. The box fastens two nuts - one in front and one behind (on a support of a rack of a suspension bracket). The General view of assemblage of an air cleaner is resulted on an illustration.

INSTALLATION

 PERFORMANCE ORDER

Installation is made upside-down. Track reliability of connection of a vacuum tube, correctness of placing of a casing of an air cleaner on the throttle case (possibility of leaks of air should be completely excluded). Check up a condition of the rubber sealing lining established from above on the case of a throttle, in case of need make replacement.