Skoda Felicia

Since 1994 of release

Repair and car operation

Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
- Engine repair
   + Repair without extraction from the car of the petrol engine of 1.3 l
   + Repair without extraction from the car of the petrol engine of 1.6 l
   - Repair without extraction from the car of the diesel engine
      The description of the basic knots and mechanisms
      Reduction of the piston of the first cylinder in position of the top dead point (ВМТ) the end of a step of compression
      Check of tightness of chambers of combustion
      Removal and installation of a belt of drive ГРМ and its covers
      Removal and installation натяжителя and cogwheels of a belt of drive ГРМ
      Removal, installation and adjustment of a tension of a belt of a drive of auxiliary units
      Removal and installation of a cover of a head of cylinders
      Replacement of an epiploon of a camshaft
      Replacement of an epiploon of an intermediate shaft
      Replacement of epiploons of a cranked shaft
      Removal and installation of a head of cylinders in gathering with the inlet pipeline and a final collector
      Check of serviceability of functioning of hydraulic pushers
      Flywheel - removal, check and installation
      Support of the power unit - check and replacement
      The pallet - removal, check and installation
      Removal and installation of the oil pump and assemblage маслозаборника
   + Dismantle of the power unit and engine major repairs
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and salon furnish
+ Onboard electric equipment

Removal and installation of the oil pump and assemblage маслозаборника

System of greasing of the diesel engine


1 — the Stopper маслозаливной mouths 2 — the Sealing lining 3 — Measuring probe 4 — the Sealing lining 5 — the Gauge-switch of a control lamp of pressure of oil 7 — the Arm of the oil filter 8 — the Bolt of fastening of an arm 9 — Consolidation 10 — the Sealing ring 11 — the Heat exchanger 12 — the Nut of fastening of the heat exchanger	13 — the Oil filter 14 — the Oil jet of a rod 15 — the Bolt of fastening of a jet 16 — Maslootrazhatel 17 — Maslootrazhatel 18 — Gear wheels of the oil pump 19 — the Cover 20 — the Fixing bolt 21 — Maslozabornik 22 — the Pallet картера 23 — the Drain stopper

Components of the oil pump


1 — pump Gear wheels 2 — a pump Cover	3 — the Sealing ring 4 — Maslozabornaja a tube

Greasing system - the general information

In the considered engine the combined system of greasing with полнопоточным the oil filter is used. The full volume of filled in oil makes 4.5 l.

Necessary working pressure of oil is created шестеренчатым by the oil pump. The width of gear wheels makes 36 mm. Маслозаборник incorporates to the pump through a sealing lining. The working size of pressure of oil in system makes 0.57 ч 0.67 мПа. At excess of admissible value there is an opening редукционного the pump valve.

The gauge-switch of a control lamp is fixed on an arm of the oil filter.

Oil cooling is made in the heat exchanger connected to system of cooling of the engine.

The oil pump and assemblage маслозаборника are located in the pallet картера the engine. The pump drive is carried out from the intermediate shaft rotating with frequency, an equal half of frequency of rotation of a cranked shaft.

REMOVAL

PERFORMANCE ORDER

1. Remove the pallet картера the engine (see Has undressed the Pallet - removal, check and installation).
2. Turn out bolts of fastening of the pump to the basis of the block of cylinders.
3. Lower assemblage of the pump with маслозаборником, having separated it from the block. At a corresponding complete set remove a plate маслоотражателя.

CHECK

PERFORMANCE ORDER

1. Give screws of fastening of a flange of interface and lift the receiver маслозаборника. Remove a sealing ring. Turn out fixing screws and uncover the pump.
2. Carefully clean the pump and check up a condition of teeths of its gear wheels.

3. For a size estimation люфта gearings повращайте gear wheels every which way. Make measurement and compare its results to requirements of Specifications.

4. By means of a steel ruler and probeа лезвийного type define axial люфт landings of gear wheels. Compare result to requirements of Specifications.

5. In case of an exit of results of measurements for limits of admissible values the pump is subject to replacement.

INSTALLATION

PERFORMANCE ORDER

1. Establish a pump cover, screw and tighten with demanded effort fixing screws.
2. Establish on the pump assemblage маслозаборника (do not forget to replace a sealing ring). Tighten fixing screws with demanded effort.
3. Establish the pump on the block of cylinders, screw and tighten with demanded effort fixing bolts.
4. Establish into place the pallet картера.